ModelState.AddModelError( "", "An unknown error occurred") įirst, extract a few properly named variables by selecting some code and hitting Ctrl + R, Ctrl + V. That Base64.DecodeID call looks like it should really be a variable called customerIdentifier to me, so I highlight Base64.DecodeID(customer.Id) and hit Ctrl + R, Ctrl + V, tell R# to call it customerIdentifier, and hit enter. At this point Resharper will also check the rest of the method to see if there are any other pieces of code that look like that, and offer to replace them as well. There are a few other things that clutter this method up a bit. The error handling is noise and looks a bit generic – I’ll put that in a separate method for now and reuse it later if I can. ![]() If I select all the code inside the catch (from the new RaygunClient() call down to the last bracket of the else) then hit Ctrl + R, Ctrl + M Resharper will offer to create a method for me.
0 Comments
I can check at the clockspring, and measured that there is continuity across the two pins for the airbag circuit (pins 3 and 4), but I don't know what that tells me. I can't check the airbag itself since there's a very good chance of setting it off. The lower resistance limit means that there's a short somewhere, but where? I've ruled out the harness. With the airbag disconnected, there's infinite resistance, hence the upper limit exceeded. This makes sense, since the airbag control module is checking the resistance across the airbag circuit. If I disconnect the airbag and clear/recheck the fault codes, I get the same code with different sub code - now it's the upper limit that's exceeded. ![]() I also checked to make sure that there wasn't a short in the harness or the connectors anywhere, and reseated the 4-pin harness going into the clockspring. I've tried all the usual remedies, including clearing the code, disconnecting/reconnecting the battery, and reseating the harness both at the clockspring and the airbag itself. My airbag light decided to come on recently, and produces the following code:Ġ0588 - Airbag Igniter Driver Side (N95) ![]() Switchable between LS UART0 and UART1.Doesn’t disconnect when base board power is cycled Attaches to 96Boards low-speed (LS) expansion connector. ![]() Source USB to RS-232/422/485, USB to SERIAL, USB CONVERTER on Taiwantrade. Find Details about USB-COMi-SI-M 1-Port RS-232/422/485 USB-to-Serial Adapter, with Optical-isolation and Surge Protection from Taiwan Industrial Computer Accessories supplier-TITAN ELECTRONICS INC. By taking advantage of the USB bus, the USB Industrial I/O Adapter makes it easier than ever to add RS-232, RS-422 or RS-485 device to your system with easy plug-and-play and hot plug features. Connecting to a USB port on your computer or USB hub, the USB-COMi + instantly adds an industrial communication port to your system. Fast transfer rates When connected to a USB 3.0 port, WD Elements portable hard drive delivers fast data transfer rates. USB 3.0 and USB 2.0 compatibility With this single drive, you get compatibility with the latest USB 3.0 devices and backward compatibility with USB 2.0 devices as well. Plus, you can connect your iOS or Android device and learn music online wi. New features such as an integrated carry handle, piano-shaped keys, longer battery life, smooth corners and a slim profile make this the perfect introduction to music. The CT-S100 keyboard is the ideal keyboard for beginners. Burroughs SmartSource Professional SmartSource Professional Elite SmartSource Micro Elite. ![]() ![]() If you don’t like to type python3.6 on terminal every time you want to execute python code then this is going to be a time saver for you. ![]() You can also check python3 and pip3 version with python3 –version and pip3 –version. Let’s check installed python3 and pip3 version on Ubuntu. ![]() configure make make test sudo make altinstall sudo apt update Check Python version on Ubuntu Or you can user wget to download python source file wget -P ~/Downloads Extract Python 3.6.12 cd ~/Downloads tar -xJf Python-3.6.12.tar.xz Install Python 3.6.12 on Ubuntu cd /Python-3.6.12. tar.xz file from or by clicking this direct download link. We are going to download Python 3.6.12 from the source and extract it sudo apt install wget make tar Uninstall Preinstalled Python3.x sudo apt remove python3 -y Download Python 3.6.12 You must have wget, make and tar installed your Ubuntu if you don’t have installed yet, you can install them with following commands. Since, I going to download and install Python 3.6.12 from the source it will take time and I also assume that you are comfortable with terminal and at the same time you should remove the preinstalled python 3.x from your system before you install python 3.6.x globally on your system. We are going to install Python 3.6.12, which is latest version of Python 3.6 with a few security fixes. This post will help install Python 3.6.10 on Ubuntu Desktop and Server. |